P0410 Secondary Air Injection Fix – Mercedes S Class W220


Mercedes P0140 Secondary Air Pump Problem 1

Mercedes Benz M113 Engine S Class S500

I have recently taken delivery of a used S Class Mercedes, 2002 model W220.  During the first few days of ownership the amber engine check lamp in the dash illuminated and stayed on. Plugging in the AUTEL diagnostics tool revealed a P0410 fault code relating to secondary air injection, so I set about troubleshooting and fixing the problem.

Mercedes P0140 Secondary Air Pump Problem 2

Remove front section of engine cover by lifting up and pulling forward.

Apart from aiding to prolonging the life of the catalysts and meeting lower emissions  targets the secondary air circuit does not effect the normal running of the vehicle if it is disabled in a particular way until a fix can be carried out.  You may remember older engines such as the 320 I6 of the R129 ran at elevated rpm’s until warm and held on to auto gear changes until the CATs were up to temperature – this is an alternate design.

Mercedes P0140 Secondary Air Pump Problem 3

Air pump mounted between the ‘V’ of the cylinder heads at the front of the M113 engine

The way to disable the system is to remove and plug the single vacuum outlet (the base of the clear thin pipe to the left in the picture above) from the control solenoid to the air check valves, one either side of the v6,v8 and v12 variants, then simply pull the control relay from the right hand fuse board in the engine compartment. Relay N. or pull fuse 31 (40A) orange.  This will accomplish two things until you get chance to repair the system, although please note it will not extinguish the engine check lamp. It will prevent any electrical current flowing to the secondary air pump and it will also prevent the air check valves on the exhaust manifolds opening with the possibility of allowing exhaust gasses to exit via the disabled air pumps delivery pipe.

Mercedes P0140 Secondary Air Pump Problem 4

People have wrongly assumed that the secondary air system only operates at start up, this is not strictly true.  What happens at a variable point during the drive cycle when certain engine conditions and running criteria are met, is that the secondary air pump is cycled for a short burst, check valves are opened and the ECM monitors and compensates for a change in the O2 levels measured in the exhaust gasses.  Here is some info on the conditions that are required to be met for a check to be made by the ECU/ECM.  It is worth noting that it takes faults to be detected on two engine start/run cycles for the engine management lamp to illuminate on the dashboard.

Mercedes P0140 Secondary Air Pump Problem 5

Mercedes – Secondary air injection pump.

It does this among other things by monitoring fuel trim and by identifying emissions changes then comparing its findings to an inbuilt reference map.  From this it can conclude that the secondary air circuit is functioning correctly – engine management is happy!  Should it detect a incorrectness or deviation from the changes expected within the combustion gas control loop, then it will flag up a secondary air injection error.  The reason it checks in this manner during the drive cycle is it can effectively test out all components in the circuit in a few seconds, air pump, air supply piping, electrical controls, check valves and actuating vacuum etc.  If even one of these control sections is giving issue, then its comparative live testing will result in a fail and flag the P0410 fault code.

Mercedes P0140 Secondary Air Pump Problem 6

Both control relay and fuse located in right hand fuse board.

On start up from cold the secondary air pump relay ‘N’ is commanded to close, this applies voltage to the air pump DC motor protected by a 40A fuse, Fuse 31.  At the same time the electrical solenoid controlling the check valve vacuum is energised, allowing vacuum to pull open both diaphragm caps.  Air is collected and pumped into the check valve heads by the twin vane air pump into a rubber supply hose that interconnects both air check valves. Air enters the open diaphragm caps and passes through a pair of non-return ‘reed’ valves into the exhaust header or manifold on each side of the engine (In a V configuration – obviously only one check valve if this system is used on any in I4 or I6 engines)  Pumped air then mixes with the combustion gasses and achieves the engineered effect of raising CAT temperature and assisting in burning off any traces of enriched combustion fuel, cleaning up its act during the initial start cycle.   The pump/blower running time is usually between 45 and 90 seconds after which the turbine will cease to rotate, check valves will close and unassisted combustion will continue.  Only after the engine has warmed up and at some further point during the current drive cycle will the system be checked once more for correct operation.

Mercedes P0140 Secondary Air Pump Problem 7

Secondary air injection control relay ‘N’ Right hand side fuse box under bonnet/hood. MB part No. A002 542 1319 Has built in coil suppressor resistor. Bosch Part number for this item cross references to: BOS 0986332040

Mercedes P0140 Secondary Air Pump Problem 8

Secondary air injection protection fuse 40A – Fuse 31- Orange Maxi-fuse

There are several faults that can occur to raise the P0410 code and resulting amber warning lamp, but often it is down to a failure of the secondary air pump itself.  What commonly happens is that the normally open TYCO power relay N ‘splashes’ its contacts and sticks closed, due in most to continued contact arcing. The relay is rated at 35/40A and the current drawn by the secondary air pump under full load can be as high as 35A which as an inductive load pushes the relay to it maximum as far as contact rating is concerned.  Once the silver contact area of the relay has deteriorated unreliable operation will result.  Worst case is that the relay sticks on and the air pump remains powered beyond its 90 second period and running continuously to its final destruction.  Relays in this circuit as well as ones in the Air-matic circuit should, in my view, be changed as a service item every 50k or so miles to attempt to prevent costly pump repairs.  A new secondary air pump from Bosch will cost in the order of £300 for the part alone and maybe £35 for the correct relay.  The resulting maths is simple.

Mercedes P0140 Secondary Air Pump Problem 9

Control Relay ‘N’ MB part No. A002 542 1319

Testing the pump is straight forward, lift up and off the front section of the plastic engine cover and remove the air pump power connector, apply 12v to the exposed contacts from an external source and listen to the sound the pump makes – if any. It should sound like a vacuum cleaner motor as it spins at a very high rate, if it sounds like its arcing or rough running its probably at end of life. If you have the means of monitoring the running current of the motor (DC clamp meter) ensure it is running to spec.  Removal is done by removing the single reverse torx set screw from the aluminium saddle plate that clamps the pump between the front of two cylinder heads.  Once this forward facing saddle plate is removed, work loose the rubber connecting hose from the pump outlet and once free, remove/jiggle the pump free from the car.  Replacement is an exact reversal of this procedure.

Mercedes P0140 Secondary Air Pump Problem 10

OBD port under dash area next to driver footwell.

The pump if faulty must be replaced along with the N control relay and if blown Fuse 31 (40A).  As it is most probable that the pump failed because of the relay it should be changed as a matter of course in all cases as we would not want the new item damaged in the same way as the old one – just for the sake of a new relay!

Mercedes P0140 Secondary Air Pump Problem 11

P0410 Faults recorded and cleared with Autel MaxiDiag Elite. Once erased you will need to cycle the ignition for this fault to fully clear.

I have dismantled both the N relay and secondary air pump so that you can how the items are made up and the issues that cause the relay to stick and the motor to self destruct, there are a few additional photographs below showing the detail of this ‘post-mortem’ carried out on the damaged parts for useful info.

Mercedes P0140 Secondary Air Pump Problem 12

Burned contacts from relay ‘N’ that stuck closed causing the secondary air pump motor to run to destruction.

Replacing the ‘N’ relay is simple, locate it in the central portion of the right hand (drivers side UK) fuse board k40/7 module or SAM in the engine bay (right side fuse box detail here), fuse 31 is there also, and is the most inboard of the three 40A orange Maxi-fuses located toward the front edge of the SAM.

Mercedes P0140 Secondary Air Pump Problem 13

Internal parts of secondary air injection pump.

Obviously when you have completed the work you will need to erase the fault code flag from the ECU with a suitable code reader, in this instance I used my Autel. The standard OBD port is under the dash next to the drivers foot well, near the bonnet release on UK cars.

Mercedes P0140 Secondary Air Pump Problem 14

Burned out rotor of the air pump, probably due to overheating.

Once the work is completed, leave off the plastic engine cover until you have started the car from cold, you can then hear the fan running and monitor at what point it shuts down (45-90 seconds after cold start) if it continues to run much beyond this time there is likely to still be a problem somewhere and you are best to disconnect the motor until it is further investigated as it is a high power, high rpm motor that is not at all rated for extended use beyond its designed short duty cycle.

It is worth checking the vacuum actuation components and piping with the pump motor housing removed, any hoses that are split or look bad should be replaced. A word of warning – do not pull or disturb the slightly thicker flexible vacuum pipe that disappears into the central ‘crutch’ between the front of the cylinder heads, if this becomes detached/broken then the complete engine has to be stripped to reattach it.  You are best to identify this hose before working in the area – In my view it is best left undisturbed!

Mercedes P0140 Secondary Air Pump Problem 15

How to safely remove the case of a power relay for inspection. Pry each side carefully with a screwdriver just enough to insert a cut section of cable tie, once all four sides are like this the relay will simply slip out of the case without damage.

In the vicinity of the black vacuum solenoid that diverts supply to the air check valves is a small blue plastic vacuum check valve, these have been known to stick and cause incorrect operation of the air injection check valves.  Often in colder weather, moisture accumulates in this device rendering it intermittent in operation, as the weather warms and it dries out then the problem disappears, only to return once the weather dips back to winter humidities again.  If you can replace this part while you are in there, do so, its cheap and readily available through the dealer parts network or from several web based pattern part sources.

Mercedes P0140 Secondary Air Pump Problem 16

Label on the air pump showing both Mercedes and Bosch part numbers, For the S500 W220 and ML320 W163 the MB part number is: A000 140 37 85 If purchasing used parts check these two numbers against your replacement.

Once you are satisfied all is well, refit the top plastic engine cover, check the fuse box lids are locked closed and clear any leaves or debris from the bulk head drain holes/flaps before shutting the bonnet and congratulating yourself on a job well done!  A job that would have cost in the region of £1000 with not much change, if it were to have been done at a Mercedes dealer.

Mercedes P0140 Secondary Air Pump Problem 17

Test cold start, listen for the pump to run and switch off anywhere between 45 and 90 seconds after start. Note – fault light cleared in this picture.

As of the 12th of March 2016 I have stock of a full set of tested used parts available (Air Pump, Relay and 40A fuse) available as a ‘kit’ to carry out this repair following the above instructions – contact me for more detail and purchase information if required  steve@mercedes.gen.in

4 thoughts on “P0410 Secondary Air Injection Fix – Mercedes S Class W220

  1. When the pump kicks on the serpentine belt squeals for a few seconds . From the current draw. But pump works and runs 45 seconds. My secondary air obd scanner says INC . So i cant pass smog. What would cause the not ready status even after several cols starts . ??? THANKS

    1. Hi Jim,
      The ‘readiness’ is just a status flag and not actually a fault code. It is just indicating the system test status as INComplete. What happens is that during a normal drive cycle after a few miles of running when the temp reaches 80C, the AC is off, throttle closed and there are no engine misfires recorded, the secondary air pump will pulse, just for a couple of seconds. This series of conditions all have to be met for the driving test (readiness check to be completed) sometimes it can take a week of driving for the flag to disappear. The readiness is checked by the ECU monitoring changes in HEGO levels in the exhaust stream and once it detects the pump is running, valves are open etc and pressure of forced air is happening then it will set the readiness flag. This means the system has been tested during the drive cycle and is ready and functional. If you have recently cleared all the ECU codes it will now look to test the secondary air system to obtain a readiness indication, proving to the ECU that all is well and functional. The fact this is an emissions system means it is required to test itself periodically and report any malfunction.

      I would be looking to check the current drawn by the motor as it is not normal for the aux drive belt to squeal during any secondary air activation, if the running current is found to be within specification then look towards replacing the drive belt/and or tensioner.

      Hope that helps

      All the best

  2. Best write up on this system I have ever seen. Even Mercedes service information is not this informative and put down in such a matter of fact, understandable way. I have repaired multiple S Class W220 sec air sys problems where the pump replacement and relay have done the job. But this last time everything seemed to work and still had p0410 coming back. Found that orange maxi fuse blown. Never had a problem with that on other cars so never even knew to check it. Problem solved thanks to you.

Leave a Reply

Your email address will not be published. Required fields are marked *